View TPD4144AK_7477663.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TPD4144AK 2012-02-15 1 toshiba intelligent power device high voltage monolithic silicon power ic TPD4144AK the TPD4144AK is a dc brush less motor driver using high voltage pwm control. it is fabricated by high voltage soi process. it is three-shunt resistor circuit for cu rrent sensing. it contains level shift high-side driver, low-side driver, igbt outputs, frds and protective functions for under vo ltage protection circuits and thermal shutdown circuit. it is easy to control a dc brush less motor by just putting logic inputs from a mpu or motor controller to the TPD4144AK. features ? high voltage power side and low voltage signal side terminal are separated. ? it is the best for current sensing in three shunt resistance. ? bootstrap circuit gives simple high-side supply. ? bootstrap diodes are built in. ? a dead time can be set as a minimum of 1.4 s, and it is the best fo r a sine-wave from drive. ? 3-phase bridge output using igbts. ? frds are built in. ? included under voltage protec tion and thermal shutdown. ? the regulator of 7v (typ.) is built in. ? package: 26-pin dip. this product has a mos structure and is sensitive to electrostatic discharge. when handling this product, ensure that the environment is protected against electrostatic discharge. hdip26-p-1332-2.00 weight: 3.8 g (typ.)
TPD4144AK 2012-02-15 2 pin assignment marking 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 gnd nc nc hu hv hw lu lv sd lw diag nc v reg nc v cc gnd u bsu is1 is2 bsv v v bb bsw w is3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 gnd nc nc hu hv hw lu lv sd lw diag nc v reg nc v cc gnd u bsu is1 is2 bsv v v bb bsw w is3 tpd4123k lot code. (weekly code) part no. (or abbreviation code) tpd 4 144a k country of origin
TPD4144AK 2012-02-15 3 block diagram low-side driver is2 gnd input logic thermal shutdown bsv bsu v bb bsw u v w high-side level shift driver 15 13 4 5 6 7 8 9 10 18 21 24 23 17 22 25 20 1/16 under- voltage protection under- voltage protection 7 v regulator 26 is3 is1 19 11 under- voltage protection v cc v reg hu hv hw lu lv lw diag sd under- voltage protection
TPD4144AK 2012-02-15 4 pin description pin no. symbol pin description 1 gnd ground pin. 2 nc unused pin, which is not connected to the chip internally. 3 nc unused pin, which is not connected to the chip internally. 4 hu the control terminal of igbt by the high side of u. it turns off less than 1.5v. it turns on more than 2.5v. 5 hv the control terminal of igbt by the high side of v. it turns off less than 1.5v. it turns on more than 2.5v. 6 hw the control terminal of igbt by the high side of w. it turns off less than 1.5v. it turns on more than 2.5v. 7 lu the control terminal of igbt by the low side of u. it turns off less than 1.5v. it turns on more than 2.5v. 8 lv the control terminal of igbt by the low side of v. it turns off less than 1.5v. it turns on more than 2.5v. 9 lw the control terminal of igbt by the low side of w. it turns off less than 1.5v. it turns on more than 2.5v. 10 sd input pin of external protection. (?l? active, it doesn't have hysteresis.) 11 diag with the diagnostic output terminal of open drai n, a pull-up is carried out by resistance. it turns on at the time of unusual. 12 nc unused pin, which is not connected to the chip internally. 13 v reg 7v regulator output pin. 14 nc unused pin, which is not connected to the chip internally. 15 v cc control power supply pin.(15v typ.) 16 gnd ground pin. 17 u u-phase output pin. 18 bsu u-phase bootstrap c apacitor connecting pin. 19 is1 u-phase igbt emitter and frd anode pin. 20 is2 v-phase igbt emitter and frd anode pin. 21 bsv v-phase bootstrap capacitor connecting pin. 22 v v-phase output pin. 23 v bb high-voltage power supply input pin. 24 bsw w-phase bootstrap capacitor connecting pin. 25 w w-phase output pin. 26 is3 w-phase igbt emitter and frd anode pin.
TPD4144AK 2012-02-15 5 equivalent circuit of input pins internal circuit diagram of hu, hv, hw, lu, lv, lw input pins internal circuit diagram of sd pin internal circuit diagram of diag pin hu/hv/hw lu/lv/lw 2 k 2 k to internal circuit 6.5 v 6.5 v 6.5 v 6.5 v 2 k 200k 2 k 2 k to internal circuit 6.5 v 6.5 v 6.5 v 6.5 v 2 k 200 k v reg sd 250k to internal circuit diag 26 v
TPD4144AK 2012-02-15 6 timing chart hu hv hw input voltage lu lv lw vu output voltage vv vw
TPD4144AK 2012-02-15 7 truth table input high side low side mode hu hv hw lu lv lw sd u phase v phase w phase u phase v phase w phase diag h l l l h l h on off off off on off off h l l l l h h on off off off off on off l h l l l h h off on off off off on off l h l h l l h off on off on off off off l l h h l l h off off on on off off off normal l l h l h l h off off on off on off off h l l l h l h off off off off off off on h l l l l h h off off off off off off on l h l l l h h off off off off off off on l h l h l l h off off off off off off on l l h h l l h off off off off off off on thermal shutdown l l h l h l h off off off off off off on h l l l h l h off off off off off off on h l l l l h h off off off off off off on l h l l l h h off off off off off off on l h l h l l h off off off off off off on l l h h l l h off off off off off off on v cc under-voltage l l h l h l h off off off off off off on h l l l h l h off off off off on off off h l l l l h h off off off off off on off l h l l l h h off off off off off on off l h l h l l h off off off on off off off l l h h l l h off off off on off off off v bs under-voltage l l h l h l h off off off off on off off sd * * * * * * l off off off off off off on
TPD4144AK 2012-02-15 8 absolute maximum ratings (ta = 25c) characteristics symbol rating unit v bb 500 v power supply voltage v cc 18 v output current (dc) i out 2 a output current (pulse 1ms) i outp 3 a input voltage v in -0.5 to 7 v v reg current i reg 50 ma diag voltage v diag 20 v diag current i diag 20 ma power dissipation igbt 1 phase (tc = 25c) ) p c(igbt) 36 w power dissipation frd1 phase (tc = 25c) ) p c(frd) 22 w operating junction temperature t jopr -40 to 135 c junction temperature t j 150 c storage temperature t stg -55 to 150 c note: using continuously under heavy loads (e.g. t he application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this pr oduct to decrease in the reliability significantly even if the operating conditions (i.e. operati ng temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and indi vidual reliability data (i.e. reliability test report and estimated failure rate, etc).
TPD4144AK 2012-02-15 9 electrical characteristics (ta = 25c) characteristics symbol test condition min typ. max unit v bb ? 50 280 450 operating power supply voltage v cc ? 13.5 15 16.5 v i bb v bb = 450 v ? ? 0.5 current dissipation i cc v cc = 15 v ? 0.8 5 ma i bs (on) v bs = 15 v, high side on ? 210 410 bootstrap current dissipation i bs (off) v bs = 15 v, high side off ? 180 370 a v ih v in = ?h?, v cc = 15 v 2.5 ? ? input voltage v il v in = ?l? , v cc = 15 v ? ? 1.5 v sd input voltage v sd v cc = 15 v ? 2.5 ? v i ih v in = 5 v ? ? 150 input current i il v in = 0 v ? ? 100 a i sdh v in = 5 v ? ? 100 sd input current i sdl v in = 0 v ? ? 150 a v cesat h v cc = 15 v, i c = 1 a, high side ? 2.3 3.2 output saturation voltage v cesat l v cc = 15 v, i c = 1 a, low side ? 2.3 3.2 v v f h i f = 1 a, high side ? 2.1 3.1 frd forward voltage v f l i f = 1 a, low side ? 2.1 3.1 v bsd forward voltage v f (bsd) i f = 500 a ? 0.8 1.2 v regulator voltage v reg v cc = 15 v, i reg = 30 ma 6.5 7 7.5 v thermal shutdown temperature tsd v cc = 15 v 135 ? 185 c thermal shutdown hysteresis tsd v cc = 15 v ? 50 ? c v cc under voltage protection v cc uvd ? 10 11 12 v v cc under voltage protection recovery v cc uvr ? 10.5 11.5 12.5 v v bs under voltage protection v bs uvd ? 8 9 9.5 v v bs under voltage protection recovery v bs uvr ? 8.5 9.5 10.5 v diag saturation voltage v diagsat i diag = 5 ma ? ? 0.5 v output on delay time t on v bb = 280 v, v cc = 15 v, i c = 1 a ? 1.2 3 s output off delay time t off v bb = 280 v, v cc = 15 v, i c = 1 a ? 1 3 s dead time t dead v bb = 280 v, v cc = 15 v, i c = 1 a 1.4 ? ? s frd reverse recovery time t rr v bb = 280 v, v cc = 15 v, i c = 1 a ? 150 ? ns
TPD4144AK 2012-02-15 10 application circuit example low-side driver v cc v reg is2 gnd input logic thermal shutdown bsv bsu v bb bsw u v w high-side level shift driver 15 13 4 5 6 7 8 hu hv hw lu lv lw 9 diag 11 18 21 24 23 17 22 25 26 1/16 7 v regulator c 4 + c 5 control ic or microcomputer c 1 c 2 c 3 r 1 c 6 + c 7 19 is1 20 is3 10 sd r 2 under- voltage protection under- voltage protection under- voltage protection under- voltage protection r c r r 15v
TPD4144AK 2012-02-15 11 external parts typical external parts are sh own in the following table. part typical purpose remarks c 1 , c 2 , c 3 25 v/2.2 f bootstrap capacitor (note 1) c 4 25 v/10 f v cc power supply stability (note 2) c 5 25 v/0.1 f v cc for surge absorber (note 2) c 6 25 v/1 f v reg power supply stability (note 2) c 7 25 v/1000 pf v reg for surge absorber (note 2) r 1 5.1 k diag pin pull-up resistor (note 3) r 2 10 k sd pin pull-up resistor - note 1: the required bootstrap capacitance value varies a ccording to the motor drive conditions. the capacitor is biased by v cc and must be sufficiently derated for it. note 2: when using this product, adjustment is required in accordance with the use environment. when mounting, place as close to the base of this product leads as possible to improve the ripple and noise elimination. note 3: the diag pin is open drain. if not using the diag pin, connect to the gnd. handling precautions please control the input signal in the state to which the v cc voltage is steady. both of the order of the v bb power supply and the v cc power supply are not cared about either. note that if the power supply is switched off as de scribed above, this product may be destroyed if the current regeneration route to the v bb power supply is blocked when the v bb line is disconnected by a relay or similar while the motor is still running. the excess voltage such as the volt age surge which exceed the absolut e maximum rating is added, for example, may destroy the circuit. accordingly, be care ful of handling this produc t or of surge voltage in its application environment.
TPD4144AK 2012-02-15 12 description of protection function (1) under voltage protection this product incorporates under vo ltage protection circuits to prevent the igbt from operating in unsaturated mode when the v cc voltage or the v bs voltage drops. when the v cc power supply falls to this product internal setting v cc uvd ( = 11 v typ.), all igbt outputs shut down regardless of the input. this prot ection function has hy steresis. when the v cc power supply reaches 0.5 v higher than the shutdown voltage (v cc uvr ( = 11.5 v typ.)), this product is automatically restored and the igbt is turned on again by the input. diag output is reversed at the time of v cc under-voltage protection. when the v cc power supply is less than 7 v, diag output isn't sometimes reversed. when the v bs supply voltage drops v bs uvd ( = 9 v typ.), the high-side igbt output shuts down. when the v bs supply voltage reaches 0.5 v higher than the shutdown voltage (v bs uvr ( = 9.5 v typ.)), the igbt is turned on ag ain by the input signal. (2) thermal shutdown this product incorporates a thermal shutdown circuit to protect itself against the abnormal state when its temperature rises excessively. when the temperature of this chip rises to the internal setting tsd due to external causes or internal heat generation, all igbt outputs shut down regard less of the input. this protection function has hysteresis tsd ( = 50 c typ.). when the chip temperature falls to tsd ? tsd, the chip is automatically restored and the igbt is turn ed on again by the input. because the chip contains just one temperature dete ction location, when the ch ip heats up due to the igbt, for example, the differences in distance from th e detection location in the igbt (the source of the heat) cause differences in the time taken for shutdown to occur. therefore, th e temperature of the chip may rise higher than the thermal shutdown temp erature when the circuit started to operate. (3) sd pin sd pin is the input signal pin to shut down the inte rnal output igbt. output of all igbt is shut down after delay times (2 s typ.) when "l" signal is inpu t to the sd pin from external circuit (mcu etc.). it is possible to shut down ic when overcurrent and others is detected by external circuit. shut down state is released by all of ic input signal "l". at open st ate of sd pin, shut down function can not operate. timing chart of under voltage protection and sd function note: the above timing chart is considering the delay time. safe operating area note 1: the above safe operating areas are tj = 135 c (figure 1). 1.9 peak winding current (a) power supply voltage v bb (v) figure 1 soa at tj = 135 c 0 450 0 400 2 sd lin ho hin v bs v cc lo diag t on t off t on t off
TPD4144AK 2012-02-15 13 frd forward voltage v f l (v) junction temperature t j (c) igbt saturation voltage v cesat h (v) junction temperature t j (c) v cesat l ? t j igbt saturation voltage v cesat l (v) junction temperature t j (c) frd forward voltage v f h (v) junction temperature t j (c) control power supply voltage v cc (v) regulator voltage v reg (v) control power supply voltage v cc (v) current dissipation i cc (ma) v cesat h ? t j 1.4 ? 50 3.8 3.4 3.0 2.2 1.8 0 50 100 150 v cc = 15 v i c = 0.8a i c = 0.4a i c = 1.2a i c = 1.6a 2.6 150 ? 50 0 50 100 v cc = 15 v i c = 0.8a i c = 0.4a i c = 1.2a i c = 1.6a 1.4 3.8 3.4 3.0 2.2 1.8 2.6 v f h ? t j ? 50 0 50 150 i f = 1.2a i f = 0.8a i f = 0.4a i f = 1.6a 100 1.2 3.2 2.8 2.0 1.6 2.4 v f l ? t j 150 0 50 100 i f = 1.2a i f = 0.8a i f = 0.4a i f = 1.6a ? 50 1.2 3.2 2.8 2.0 1.6 2.4 i cc ? v cc 0 12 2.0 0.5 1.0 1.5 14 16 18 v reg ? v cc 18 6.0 12 6.5 7.0 7.5 14 16 8.0 t j = ? 40c t j =25c t j =135c i reg = 30 ma t j = ? 40c t j =25c t j =135c
TPD4144AK 2012-02-15 14 t off ? t j 0 3.0 1.0 2.0 ? 50 0 50 100 150 t on ? t j ? 50 0 50 100 150 0 3.0 1.0 2.0 under-voltage protection operating voltage v cc uv (v) junction temperature t j (c) junction temperature t j (c) v bb = 280 v v cc = 15 v i c = 1 a high-side low-side v bb = 280 v v cc = 15 v i c = 1 a high-side low-side under-voltage protection operating voltage v bs uv (v) junction temperature t j (c) output-on delay time t on ( s) junction temperature t j (c) output-off delay time t off ( s) v cc uv ? t j ? 50 0 50 100 150 10.0 11.5 11.0 v cc uvd v cc uvr 12.0 12.5 10.5 v bs uv ? t j 0 50 100 150 10.5 8.0 10.0 8.5 9.5 9.0 v bs uvd v bs uvr ? 50
TPD4144AK 2012-02-15 15 bootstrap voltage v bs (v) bootstrap current dissipation i bs (on) ( a) bootstrap current dissipation i bs (off) ( a) turn-on loss wton ( j) junction temperature t j (c) junction temperature t j (c) turn-off loss wtoff ( j) bootstrap voltage v bs (v) i bs (off) ? v bs i bs (on) ? v bs 100 12 0 200 400 14 16 18 t j = ? 40c t j =25c t j =135c 18 12 14 16 t j = ? 40c t j =25c t j =135c 300 100 0 200 400 300 w ton ? t j ? 50 0 50 100 150 w toff ? t j 0 ? 50 80 60 40 20 0 50 100 150 i c = 1.2a i c = 0.8a i c = 0.4a i c = 0.8a i c = 1.2a i c = 1.6a i c = 1.6a i c = 0.4a 0 200 150 100 50 100
TPD4144AK 2012-02-15 16 test circuits igbt saturation voltage (u-phase low side) frd forward voltage (u-phase low side) lw = 0v v cc = 15v 1 gnd 2 nc 3 nc 4 hu 5 hv 6 hw 7 lu 8 lv 9 lw 10 sd 11 diag 12 nc 13 v reg 14 nc 15 v cc 16 gnd 17 u 18 bsu 19 is1 20 is2 21 bsv 22 v 23 v bb 24 bsw 25 w 26 is3 hw = 0v lu = 5v 1 a vm lv = 0v hv = 0v hu = 0v 1 a 1 gnd 2 nc 3 nc 4 hu 5 hv 6 hw 7 lu 8 lv 9 lw 10 sd 11 diag 12 nc 13 v reg 14 nc 15 v cc 16 gnd 17 u 18 bsu 19 is1 20 is2 21 bsv 22 v 23 v bb 24 bsw 25 w 26 is3 vm
TPD4144AK 2012-02-15 17 v cc current dissipation regulator voltage im v cc = 15v 1 gnd 2 nc 3 nc 4 hu 5 hv 6 hw 7 lu 8 lv 9 lw 10 sd 11 diag 12 nc 13 v reg 14 nc 15 v cc 16 gnd 17 u 18 bsu 19 is1 20 is2 21 bsv 22 v 23 v bb 24 bsw 25 w 26 is3 vm v cc = 15v 30ma 1 gnd 2 nc 3 nc 4 hu 5 hv 6 hw 7 lu 8 lv 9 lw 10 sd 11 diag 12 nc 13 v reg 14 nc 15 v cc 16 gnd 17 u 18 bsu 19 is1 20 is2 21 bsv 22 v 23 v bb 24 bsw 25 w 26 is3
TPD4144AK 2012-02-15 18 output on/off delay time (u-phase low side) im u = 280v 280? 2.2 f lw = 0v v cc = 15v hw = 0v lu = pg lv = 0v hv = 0v hu = 0v 1 gnd 2 nc 3 nc 4 hu 5 hv 6 hw 7 lu 8 lv 9 lw 10 sd 11 diag 12 nc 13 v reg 14 nc 15 v cc 16 gnd 17 u 18 bsu 19 is1 20 is2 21 bsv 22 v 23 v bb 24 bsw 25 w 26 is3 lu = pg im t on t off 10% 10% 90% 90% 5v
TPD4144AK 2012-02-15 19 v cc under-voltage protection operating/recovery voltage (u-phase low side) *:note: sweeps the v cc pin voltage from 15 v and monitors the u pin voltage. the v cc pin voltage when output is off defines t he under voltage protection operating voltage. also sweeps from 6 v to increase. the v cc pin voltage when output is on defi nes the under voltage protection recovery voltage. v bs under voltage protection operating/recovery voltage (u-phase high side) *:note: sweeps the bsu pin voltage from 15 v to decrease and monitors the v bb pin voltage.the bsu pin voltage when output is off defines the under voltage protection operating voltage.also swe eps the bsu pin voltage from 6 v to increase and change the hu pin voltage at 5 v 0 v 5 v each time. it repeats similarly output is on. when the bsu pin voltage when output is on defines the under voltage protection recovery voltage. vm u = 18v 2k ? 6v 15v v cc = 15v 6v lw = 0v hw = 0v lu = 5v lv = 0v hv = 0v hu = 0v d 1 gnd d 2 nc d 3 nc d 4 hu d 5 hv d 6 hw d 7 lu d 8 lv d 9 lw d 10 sd d 11 diag d 12 nc d 13 v reg d 14 nc d 15 v cc d 16 gnd d 17 u d 18 bsu d 19 is1 d 20 is2 d 21 bsv d 22 v d 23 v bb d 24 bsw d 25 w d 26 is3 lw = 0v v cc = 15v hw = 0v lu = 0v lv = 0v hv = 0v hu = 5v d 1 gnd d 2 nc d 3 nc d 4 hu d 5 hv d 6 hw d 7 lu d 8 lv d 9 lw d 10 sd d 11 diag d 12 nc d 13 v reg d 14 nc d 15 v cc d 16 gnd bsu = 15v 6v vm 2k ? v bb = 18v 6v 15v d 17 u d 18 bsu d 19 is1 d 20 is2 d 21 bsv d 22 v d 23 v bb d 24 bsw d 25 w d 26 is3
TPD4144AK 2012-02-15 20 bootstrap current dissipation (u-phase high side) hu = 0v/5v bsu = 15v lw = 0v v cc = 15v hw = 0v lu = 0v lv = 0v hv = 0v 1 gnd 2 nc 3 nc 4 hu 5 hv 6 hw 7 lu 8 lv 9 lw 10 sd 11 diag 12 nc 13 v reg 14 nc 15 v cc 16 gnd 17 u 18 bsu 19 is1 20 is2 21 bsv 22 v 23 v bb 24 bsw 25 w 26 is3 im
TPD4144AK 2012-02-15 21 turn-on/off loss (low side igbt + high side frd) lw = 0v v cc = 15v hw = 0v lu = pg lv = 0v hv = 0v hu = 0v im l vm 5mh 2.2 f input (lu = pg) igbt (c-e voltage) (u-gnd) power supply current w toff w ton d 1 gnd d 2 nc d 3 nc d 4 hu d 5 hv d 6 hw d 7 lu d 8 lv d 9 lw d 10 sd d 11 diag d 12 nc d 13 v reg d 14 nc d 15 v cc d 16 gnd d 17 u d 18 bsu d 19 is1 d 20 is2 d 21 bsv d 22 v d 23 v bb d 24 bsw d 25 w d 26 is3 v bb /u = 280v
TPD4144AK 2012-02-15 22 package dimensions hdip26-p-1332-2.00 unit : mm weight: 3.8 g (typ.)
TPD4144AK 2012-02-15 23 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively ?toshiba?), reserve the right to make changes to the in formation in this document, and related hardware, software and systems (collectively ?product?) without notice. ? this document and any information herein may not be reproduced wi thout prior written permission from toshiba. even with toshib a?s written permission, reproduction is permissible only if reproduction is without alteration/omission. ? though toshiba works continually to improve product?s quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a ma lfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. befo re customers use the product, create designs including the produc t, or incorporate the product into their own applications, customers must also refer to and comply with (a) the latest versions of al l relevant toshiba information, including without limitation, this document, the specifications, the data sheets and application notes for product and the precautions and conditions set forth in the ?toshiba se miconductor reliability handbook? a nd (b) the instructions for t he application with which the product will be used with or for. custom ers are solely responsible for all aspects of their own prod uct design or applications, including but not limited to (a) determining the appropriateness of the use of this product in such design or applications; (b) evaluating and determining the applicability of any information contained in th is document, or in charts, diagrams, program s, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating parameters for suc h designs and applications. toshiba assumes no liability for customers? product design or applications. ? product is intended for use in general el ectronics applications (e.g., computers, personal equipment, office equipment, measur ing equipment, industrial robots and home electroni cs appliances) or for specif ic applications as expre ssly stated in this document . product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or re liability and/or a malfunction or failure of which may cause loss of hum an life, bodily injury, serious property damage or serious public impact (?unintended use?). unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the ae rospace industry, medical equipment, equipment used for automobiles, tr ains, ships and other transportation, traffic signaling equipmen t, equipment used to control combustions or ex plosions, safety devices, elevators and esca lators, devices related to electric powe r, and equipment used in finance-related fields. do not use product for unintended use unle ss specifically permitted in this document. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is pres ented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this document, w hether express or implied, by estoppel or otherwise. ? a bsent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation, indirect, consequential, special, or incidental damages or loss, including without limitation, loss of profits, loss of opportunities, busin ess interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditio ns of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? do not use or otherwise make available product or related so ftware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile technolog y products (mass destruction weapons). product and related softwa re and technology may be controlled under the japanese foreign exchange and foreign trade law and the u.s. export administration regulations. export and re-export of product or related softw are or technology are strictly prohibited except in comp liance with all applicable ex port laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result o f noncompliance with applicable laws and regulations.

▲Up To Search▲

Price & Availability of TPD4144AK

	To Download TPD4144AK Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .